What are the types of car anti-theft locks?

[ Huaqiang Security Network News ]
Do you know the types of car anti-theft locks? According to the technical principle, the car anti-theft lock can be basically divided into three categories: mechanical anti-theft lock, electronic anti-theft alarm lock, and networked anti-theft (positioning, tracking) system. Car anti-theft locks include: electronic car anti-theft lock, network car anti-theft lock, oil road lock, clutch brake anti-theft lock, wheel anti-theft lock, gear lock, steering wheel lock, car anti-theft disk.
Car lock type
What are the types of car anti-theft locks?
Car anti-theft lock type
According to the technical principle, the car anti-theft lock can be basically divided into three categories: mechanical anti-theft lock, electronic anti-theft alarm lock, and networked anti-theft (positioning, tracking) system. Increasing the complexity of mechanical locks can no longer meet the existing technology, electronic burglar alarms are only used to make up for the dead, and there are drawbacks in the anti-theft measures that are not integrated into the engine control system. For example, if a circuit breaker is added to the power supply line of the ignition coil, it is easy to find the line bypassing the circuit breaker; or the power failure of the alarm can be released. Integrated into the ECU's anti-theft measures, if the anti-theft state is not removed, the ECU will refuse to work. The engine is definitely unable to start, and the anti-theft system is safer and more reliable.
Electronic car anti-theft lock
The electronic car anti-theft device can send buzzer, siren, light and other signals when the thief enters the car, which can scare off the thief and attract the attention of passers-by. There are many types of electronic anti-theft systems, and there is a special remote control. There are many such anti-theft devices on the market, but there are very few technical clearances. The installation of electronic anti-theft devices needs to be rerouted to destroy the original car circuit. If the vehicle has a spontaneous combustion accident, some insurance companies will install the anti-theft device according to their own reasons. Rejecting compensation, this has to be highly valued. In addition, the signal jammer on the market can interfere with most electronic anti-theft devices, making the lock car invalid.
Network car anti-theft lock
The network car anti-theft device, also known as GPS, uses a satellite positioning system to monitor the car. The principle is to input the vehicle information into the phone card and install it in the GPS locator, and then install it in the concealed position inside the car to monitor the position of the car. If the car is stolen, the owner can know the specific location through the SIM card. At the same time, the GPS management terminal has better scalability, and can realize remote fuel cut and information feedback query. Different functions and different prices, compared with electronic anti-theft devices, GPS anti-theft is more intelligent and more active.

Wire threaded sleeve: A spiral made of diamond-shaped wire. The outer surface forms an external thread and the inner surface forms an internal thread. Mounting handle: A straight shank that is bent inward at one end of the wire threaded sleeve. Specially used to screw the wire screw into the screw hole. When installing the wire screw sleeve, use a special tool to pass through the wire screw sleeve, clamp the mounting handle, and screw the diameter of the wire screw sleeve to screw the wire screw sleeve into the screw hole. Guidance: At the end of the wire screw sleeve mounting handle, the diameter of the wire screw sleeve within 210 degrees of the mounting handle is reduced, so that the end of the wire screw sleeve can smoothly enter the screw hole when the screw thread is screwed into the screw hole. This section of the wire screw sleeve is called the guide. Folding end groove: A notch designed to remove the mounting handle. After the wire screw is screwed into the screw hole, the mounting handle loses its effect, which in turn affects the screw passing through the wire screw sleeve. In some cases, the mounting handle needs to be removed so that the screw is not obstructed by the threaded screw. To this end, a notch is formed in the guide section at 30 to 90 degrees from the mounting handle so that the mounting handle can be broken therefrom when the mounting handle is impacted by a tool.

helicoil insert

recoil insert

Tanged Thread Insert

Threaded Inserts For Metal,Tanged Free Running Insert,High Precision Wire Thread Insert,Tanged Thread Insert

Xinxiang Donghai Industry Co., Ltd. , https://www.nbtmzz.com